This driver was merged in 2011 as a tool for detecting the orientation of a screen. The device driver assumes board file setup using the platform data from <linux/input/gpio_tilt.h>. But no boards in the kernel tree defines this platform data. As I am faced with refactoring drivers to use GPIO descriptors and pass decriptor tables from boards, or use the device tree device drivers like these creates a serious problem: I cannot fix them and cannot test them, not even compile-test them with a system actually using it (no in-tree boardfile). I suggest to delete this driver and rewrite it using device tree if it is still in use on actively maintained systems. I can also offer to rewrite it out of the blue using device tree if someone promise to test it and help me iterate it.
Showing the changes to include/linux/input (1 of 6 files). Show all
Unified · Split
| @@ -1,74 +0,0 @@ | ||
| 1 | −/* SPDX-License-Identifier: GPL-2.0 */ | |
| 2 | −#ifndef _INPUT_GPIO_TILT_H | |
| 3 | −#define _INPUT_GPIO_TILT_H | |
| 4 | − | |
| 5 | −/** | |
| 6 | − * struct gpio_tilt_axis - Axis used by the tilt switch | |
| 7 | − * @axis: Constant describing the axis, e.g. ABS_X | |
| 8 | − * @min: minimum value for abs_param | |
| 9 | − * @max: maximum value for abs_param | |
| 10 | − * @fuzz: fuzz value for abs_param | |
| 11 | − * @flat: flat value for abs_param | |
| 12 | − */ | |
| 13 | −struct gpio_tilt_axis { | |
| 14 | − int axis; | |
| 15 | − int min; | |
| 16 | − int max; | |
| 17 | − int fuzz; | |
| 18 | − int flat; | |
| 19 | −}; | |
| 20 | − | |
| 21 | −/** | |
| 22 | − * struct gpio_tilt_state - state description | |
| 23 | − * @gpios: bitfield of gpio target-states for the value | |
| 24 | − * @axes: array containing the axes settings for the gpio state | |
| 25 | − * The array indizes must correspond to the axes defined | |
| 26 | − * in platform_data | |
| 27 | − * | |
| 28 | − * This structure describes a supported axis settings | |
| 29 | − * and the necessary gpio-state which represent it. | |
| 30 | − * | |
| 31 | − * The n-th bit in the bitfield describes the state of the n-th GPIO | |
| 32 | − * from the gpios-array defined in gpio_regulator_config below. | |
| 33 | − */ | |
| 34 | −struct gpio_tilt_state { | |
| 35 | − int gpios; | |
| 36 | − int *axes; | |
| 37 | −}; | |
| 38 | − | |
| 39 | −/** | |
| 40 | − * struct gpio_tilt_platform_data | |
| 41 | − * @gpios: Array containing the gpios determining the tilt state | |
| 42 | − * @nr_gpios: Number of gpios | |
| 43 | − * @axes: Array of gpio_tilt_axis descriptions | |
| 44 | − * @nr_axes: Number of axes | |
| 45 | − * @states: Array of gpio_tilt_state entries describing | |
| 46 | − * the gpio state for specific tilts | |
| 47 | − * @nr_states: Number of states available | |
| 48 | − * @debounce_interval: debounce ticks interval in msecs | |
| 49 | − * @poll_interval: polling interval in msecs - for polling driver only | |
| 50 | − * @enable: callback to enable the tilt switch | |
| 51 | − * @disable: callback to disable the tilt switch | |
| 52 | − * | |
| 53 | − * This structure contains gpio-tilt-switch configuration | |
| 54 | − * information that must be passed by platform code to the | |
| 55 | − * gpio-tilt input driver. | |
| 56 | − */ | |
| 57 | −struct gpio_tilt_platform_data { | |
| 58 | − struct gpio *gpios; | |
| 59 | − int nr_gpios; | |
| 60 | − | |
| 61 | − struct gpio_tilt_axis *axes; | |
| 62 | − int nr_axes; | |
| 63 | − | |
| 64 | − struct gpio_tilt_state *states; | |
| 65 | − int nr_states; | |
| 66 | − | |
| 67 | − int debounce_interval; | |
| 68 | − | |
| 69 | − unsigned int poll_interval; | |
| 70 | − int (*enable)(struct device *dev); | |
| 71 | − void (*disable)(struct device *dev); | |
| 72 | −}; | |
| 73 | − | |
| 74 | −#endif | |