#ifndef _RAID1_H#define _RAID1_H struct mirror_info {	struct md_rdev	*rdev;	sector_t	head_position;}; /* * memory pools need a pointer to the mddev, so they can force an unplug * when memory is tight, and a count of the number of drives that the * pool was allocated for, so they know how much to allocate and free. * mddev->raid_disks cannot be used, as it can change while a pool is active * These two datums are stored in a kmalloced struct. * The 'raid_disks' here is twice the raid_disks in r1conf. * This allows space for each 'real' device can have a replacement in the * second half of the array. */ struct pool_info {	struct mddev *mddev;	int	raid_disks;}; struct r1conf {	struct mddev		*mddev;	struct mirror_info	*mirrors;	/* twice 'raid_disks' to						 * allow for replacements.						 */	int			raid_disks; 	/* When choose the best device for a read (read_balance())	 * we try to keep sequential reads one the same device	 * using 'last_used' and 'next_seq_sect'	 */	int			last_used;	sector_t		next_seq_sect;	/* During resync, read_balancing is only allowed on the part	 * of the array that has been resynced.  'next_resync' tells us	 * where that is.	 */	sector_t		next_resync; 	spinlock_t		device_lock; 	/* list of 'struct r1bio' that need to be processed by raid1d,	 * whether to retry a read, writeout a resync or recovery	 * block, or anything else.	 */	struct list_head	retry_list; 	/* queue pending writes to be submitted on unplug */	struct bio_list		pending_bio_list;	int			pending_count; 	/* for use when syncing mirrors:	 * We don't allow both normal IO and resync/recovery IO at	 * the same time - resync/recovery can only happen when there	 * is no other IO.  So when either is active, the other has to wait.	 * See more details description in raid1.c near raise_barrier().	 */	wait_queue_head_t	wait_barrier;	spinlock_t		resync_lock;	int			nr_pending;	int			nr_waiting;	int			nr_queued;	int			barrier; 	/* Set to 1 if a full sync is needed, (fresh device added).	 * Cleared when a sync completes.	 */	int			fullsync; 	/* When the same as mddev->recovery_disabled we don't allow	 * recovery to be attempted as we expect a read error.	 */	int			recovery_disabled;  	/* poolinfo contains information about the content of the	 * mempools - it changes when the array grows or shrinks	 */	struct pool_info	*poolinfo;	mempool_t		*r1bio_pool;	mempool_t		*r1buf_pool; 	/* temporary buffer to synchronous IO when attempting to repair	 * a read error.	 */	struct page		*tmppage;  	/* When taking over an array from a different personality, we store	 * the new thread here until we fully activate the array.	 */	struct md_thread	*thread;}; /* * this is our 'private' RAID1 bio. * * it contains information about what kind of IO operations were started * for this RAID1 operation, and about their status: */ struct r1bio {	atomic_t		remaining; /* 'have we finished' count,					    * used from IRQ handlers					    */	atomic_t		behind_remaining; /* number of write-behind ios remaining						 * in this BehindIO request						 */	sector_t		sector;	int			sectors;	unsigned long		state;	struct mddev		*mddev;	/*	 * original bio going to /dev/mdx	 */	struct bio		*master_bio;	/*	 * if the IO is in READ direction, then this is where we read	 */	int			read_disk; 	struct list_head	retry_list;	/* Next two are only valid when R1BIO_BehindIO is set */	struct bio_vec		*behind_bvecs;	int			behind_page_count;	/*	 * if the IO is in WRITE direction, then multiple bios are used.	 * We choose the number when they are allocated.	 */	struct bio		*bios[0];	/* DO NOT PUT ANY NEW FIELDS HERE - bios array is contiguously alloced*/}; /* when we get a read error on a read-only array, we redirect to another * device without failing the first device, or trying to over-write to * correct the read error.  To keep track of bad blocks on a per-bio * level, we store IO_BLOCKED in the appropriate 'bios' pointer */#define IO_BLOCKED ((struct bio *)1)/* When we successfully write to a known bad-block, we need to remove the * bad-block marking which must be done from process context.  So we record * the success by setting bios[n] to IO_MADE_GOOD */#define IO_MADE_GOOD ((struct bio *)2) #define BIO_SPECIAL(bio) ((unsigned long)bio <= 2) /* bits for r1bio.state */#define	R1BIO_Uptodate	0#define	R1BIO_IsSync	1#define	R1BIO_Degraded	2#define	R1BIO_BehindIO	3/* Set ReadError on bios that experience a readerror so that * raid1d knows what to do with them. */#define R1BIO_ReadError 4/* For write-behind requests, we call bi_end_io when * the last non-write-behind device completes, providing * any write was successful.  Otherwise we call when * any write-behind write succeeds, otherwise we call * with failure when last write completes (and all failed). * Record that bi_end_io was called with this flag... */#define	R1BIO_Returned 6/* If a write for this request means we can clear some * known-bad-block records, we set this flag */#define	R1BIO_MadeGood 7#define	R1BIO_WriteError 8 extern int md_raid1_congested(struct mddev *mddev, int bits); #endif