# SPDX-License-Identifier: GPL-2.0-only## Touchscreen driver configuration#menuconfig INPUT_TOUCHSCREEN bool "Touchscreens" help Say Y here, and a list of supported touchscreens will be displayed. This option doesn't affect the kernel. If unsure, say Y. if INPUT_TOUCHSCREEN config TOUCHSCREEN_88PM860X tristate "Marvell 88PM860x touchscreen" depends on MFD_88PM860X help Say Y here if you have a 88PM860x PMIC and want to enable support for the built-in touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called 88pm860x-ts. config TOUCHSCREEN_ADS7846 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller, and your board-specific setup code includes that in its table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ads7846. config TOUCHSCREEN_AD7877 tristate "AD7877 based touchscreens" depends on SPI_MASTER help Say Y here if you have a touchscreen interface using the AD7877 controller, and your board-specific initialization code includes that in its table of SPI devices. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7877. config TOUCHSCREEN_AD7879 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface" help Say Y here if you want to support a touchscreen interface using the AD7879-1/AD7889-1 controller. You should select a bus connection too. To compile this driver as a module, choose M here: the module will be called ad7879. config TOUCHSCREEN_AD7879_I2C tristate "support I2C bus connection" depends on TOUCHSCREEN_AD7879 && I2C select REGMAP_I2C help Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called ad7879-i2c. config TOUCHSCREEN_AD7879_SPI tristate "support SPI bus connection" depends on TOUCHSCREEN_AD7879 && SPI_MASTER select REGMAP_SPI help Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7879-spi. config TOUCHSCREEN_ADC tristate "Generic ADC based resistive touchscreen" depends on IIO select IIO_BUFFER select IIO_BUFFER_CB help Say Y here if you want to use the generic ADC resistive touchscreen driver. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called resistive-adc-touch.ko. config TOUCHSCREEN_APPLE_Z2 tristate "Apple Z2 touchscreens" depends on SPI && (ARCH_APPLE || COMPILE_TEST) help Say Y here if you have an ARM Apple device with a touchscreen or a touchbar. If unsure, say N. To compile this driver as a module, choose M here: the module will be called apple_z2. config TOUCHSCREEN_AR1021_I2C tristate "Microchip AR1020/1021 i2c touchscreen" depends on I2C && OF help Say Y here if you have the Microchip AR1020 or AR1021 touchscreen controller chip in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called ar1021_i2c. config TOUCHSCREEN_ATMEL_MXT tristate "Atmel mXT I2C Touchscreen" depends on I2C select FW_LOADER help Say Y here if you have Atmel mXT series I2C touchscreen, such as AT42QT602240/ATMXT224, connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called atmel_mxt_ts. config TOUCHSCREEN_ATMEL_MXT_T37 bool "Support T37 Diagnostic Data" depends on TOUCHSCREEN_ATMEL_MXT depends on VIDEO_DEV=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_DEV=m) select VIDEOBUF2_VMALLOC help Say Y here if you want support to output data from the T37 Diagnostic Data object using a V4L device. config TOUCHSCREEN_AUO_PIXCIR tristate "AUO in-cell touchscreen using Pixcir ICs" depends on I2C depends on GPIOLIB || COMPILE_TEST help Say Y here if you have a AUO display with in-cell touchscreen using Pixcir ICs. If unsure, say N. To compile this driver as a module, choose M here: the module will be called auo-pixcir-ts. config TOUCHSCREEN_BU21013 tristate "BU21013 based touch panel controllers" depends on I2C help Say Y here if you have a bu21013 touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called bu21013_ts. config TOUCHSCREEN_BU21029 tristate "Rohm BU21029 based touch panel controllers" depends on I2C help Say Y here if you have a Rohm BU21029 touchscreen controller connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called bu21029_ts. config TOUCHSCREEN_CHIPONE_ICN8318 tristate "chipone icn8318 touchscreen controller" depends on GPIOLIB || COMPILE_TEST depends on I2C depends on OF help Say Y here if you have a ChipOne icn8318 based I2C touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called chipone_icn8318. config TOUCHSCREEN_CHIPONE_ICN8505 tristate "chipone icn8505 touchscreen controller" depends on I2C && ACPI help Say Y here if you have a ChipOne icn8505 based I2C touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called chipone_icn8505. config TOUCHSCREEN_CY8CTMA140 tristate "cy8ctma140 touchscreen" depends on I2C help Say Y here if you have a Cypress CY8CTMA140 capacitive touchscreen also just known as "TMA140" If unsure, say N. To compile this driver as a module, choose M here: the module will be called cy8ctma140. config TOUCHSCREEN_CY8CTMG110 tristate "cy8ctmg110 touchscreen" depends on I2C depends on GPIOLIB || COMPILE_TEST help Say Y here if you have a cy8ctmg110 capacitive touchscreen on an AAVA device. If unsure, say N. To compile this driver as a module, choose M here: the module will be called cy8ctmg110_ts. config TOUCHSCREEN_CYTTSP_CORE tristate "Cypress TTSP touchscreen" help Say Y here if you have a touchscreen using controller from the Cypress TrueTouch(tm) Standard Product family connected to your system. You will also need to select appropriate bus connection below. If unsure, say N. To compile this driver as a module, choose M here: the module will be called cyttsp_core. config TOUCHSCREEN_CYTTSP_I2C tristate "support I2C bus connection" depends on TOUCHSCREEN_CYTTSP_CORE && I2C help Say Y here if the touchscreen is connected via I2C bus. To compile this driver as a module, choose M here: the module will be called cyttsp_i2c. config TOUCHSCREEN_CYTTSP_SPI tristate "support SPI bus connection" depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER help Say Y here if the touchscreen is connected via SPI bus. To compile this driver as a module, choose M here: the module will be called cyttsp_spi. config TOUCHSCREEN_CYTTSP5 tristate "Cypress TrueTouch Gen5 Touchscreen Driver" depends on I2C select REGMAP_I2C select CRC_ITU_T help Driver for Parade TrueTouch Standard Product Generation 5 touchscreen controllers. I2C bus interface support only. Say Y here if you have a Cypress Gen5 touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called cyttsp5. config TOUCHSCREEN_DA9034 tristate "Touchscreen support for Dialog Semiconductor DA9034" depends on PMIC_DA903X default y help Say Y here to enable the support for the touchscreen found on Dialog Semiconductor DA9034 PMIC. If unsure, say N. To compile this driver as a module, choose M here: the module will be called da9034-ts. config TOUCHSCREEN_DA9052 tristate "Dialog DA9052/DA9053 TSI" depends on PMIC_DA9052 help Say Y here to support the touchscreen found on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs. If unsure, say N. To compile this driver as a module, choose M here: the module will be called da9052_tsi. config TOUCHSCREEN_DYNAPRO tristate "Dynapro serial touchscreen" select SERIO help Say Y here if you have a Dynapro serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called dynapro. config TOUCHSCREEN_HAMPSHIRE tristate "Hampshire serial touchscreen" select SERIO help Say Y here if you have a Hampshire serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hampshire. config TOUCHSCREEN_EETI tristate "EETI touchscreen panel support" depends on I2C help Say Y here to enable support for I2C connected EETI touch panels. To compile this driver as a module, choose M here: the module will be called eeti_ts. config TOUCHSCREEN_EGALAX tristate "EETI eGalax multi-touch panel support" depends on I2C && OF help Say Y here to enable support for I2C connected EETI eGalax multi-touch panels. To compile this driver as a module, choose M here: the module will be called egalax_ts. config TOUCHSCREEN_EGALAX_SERIAL tristate "EETI eGalax serial touchscreen" select SERIO help Say Y here to enable support for serial connected EETI eGalax touch panels. To compile this driver as a module, choose M here: the module will be called egalax_ts_serial. config TOUCHSCREEN_EXC3000 tristate "EETI EXC3000 multi-touch panel support" depends on I2C help Say Y here to enable support for I2C connected EETI EXC3000 multi-touch panels. To compile this driver as a module, choose M here: the module will be called exc3000. config TOUCHSCREEN_FUJITSU tristate "Fujitsu serial touchscreen" select SERIO help Say Y here if you have the Fujitsu touchscreen (such as one installed in Lifebook P series laptop) connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called fujitsu-ts. config TOUCHSCREEN_GOODIX tristate "Goodix I2C touchscreen" depends on I2C depends on GPIOLIB || COMPILE_TEST help Say Y here if you have the Goodix touchscreen (such as one installed in Onda v975w tablets) connected to your system. It also supports 5-finger chip models, which can be found on ARM tablets, like Wexler TAB7200 and MSI Primo73. If unsure, say N. To compile this driver as a module, choose M here: the module will be called goodix. config TOUCHSCREEN_GOODIX_BERLIN_CORE tristate config TOUCHSCREEN_GOODIX_BERLIN_I2C tristate "Goodix Berlin I2C touchscreen" depends on I2C select REGMAP_I2C select TOUCHSCREEN_GOODIX_BERLIN_CORE help Say Y here if you have a Goodix Berlin IC connected to your system via I2C. If unsure, say N. To compile this driver as a module, choose M here: the module will be called goodix_berlin_i2c. config TOUCHSCREEN_GOODIX_BERLIN_SPI tristate "Goodix Berlin SPI touchscreen" depends on SPI_MASTER select REGMAP select TOUCHSCREEN_GOODIX_BERLIN_CORE help Say Y here if you have a Goodix Berlin IC connected to your system via SPI. If unsure, say N. To compile this driver as a module, choose M here: the module will be called goodix_berlin_spi. config TOUCHSCREEN_HIDEEP tristate "HiDeep Touch IC" depends on I2C select REGMAP_I2C help Say Y here if you have a touchscreen using HiDeep. If unsure, say N. To compile this driver as a module, choose M here : the module will be called hideep_ts. config TOUCHSCREEN_HIMAX_HX852X tristate "Himax HX852x(ES) touchscreen" depends on I2C help Say Y here if you have a Himax HX852x(ES) touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called himax_hx852x. config TOUCHSCREEN_HYCON_HY46XX tristate "Hycon hy46xx touchscreen support" depends on I2C select REGMAP_I2C help Say Y here if you have a touchscreen using Hycon hy46xx If unsure, say N. To compile this driver as a module, choose M here: the module will be called hycon-hy46xx. config TOUCHSCREEN_HYNITRON_CSTXXX tristate "Hynitron touchscreen support" depends on I2C help Say Y here if you have a touchscreen using a Hynitron touchscreen controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hynitron-cstxxx. config TOUCHSCREEN_HYNITRON_CST816X tristate "Hynitron CST816x touchscreen" depends on I2C help Say Y here if you have a touchscreen using a Hynitron CST816x series touchscreen controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hynitron-cst816x. config TOUCHSCREEN_ILI210X tristate "Ilitek ILI210X based touchscreen" depends on I2C select CRC_CCITT help Say Y here if you have a ILI210X based touchscreen controller. This driver supports models ILI2102, ILI2102s, ILI2103, ILI2103s and ILI2105. Such kind of chipsets can be found in Amazon Kindle Fire touchscreens. Lines 1–500 of 1417. Load more
# SPDX-License-Identifier: GPL-2.0-only # # Touchscreen driver configuration # menuconfig INPUT_TOUCHSCREEN bool "Touchscreens" help Say Y here, and a list of supported touchscreens will be displayed. This option doesn't affect the kernel. If unsure, say Y. if INPUT_TOUCHSCREEN config TOUCHSCREEN_88PM860X tristate "Marvell 88PM860x touchscreen" depends on MFD_88PM860X help Say Y here if you have a 88PM860x PMIC and want to enable support for the built-in touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called 88pm860x-ts. config TOUCHSCREEN_ADS7846 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller, and your board-specific setup code includes that in its table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ads7846. config TOUCHSCREEN_AD7877 tristate "AD7877 based touchscreens" depends on SPI_MASTER help Say Y here if you have a touchscreen interface using the AD7877 controller, and your board-specific initialization code includes that in its table of SPI devices. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7877. config TOUCHSCREEN_AD7879 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface" help Say Y here if you want to support a touchscreen interface using the AD7879-1/AD7889-1 controller. You should select a bus connection too. To compile this driver as a module, choose M here: the module will be called ad7879. config TOUCHSCREEN_AD7879_I2C tristate "support I2C bus connection" depends on TOUCHSCREEN_AD7879 && I2C select REGMAP_I2C help Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called ad7879-i2c. config TOUCHSCREEN_AD7879_SPI tristate "support SPI bus connection" depends on TOUCHSCREEN_AD7879 && SPI_MASTER select REGMAP_SPI help Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ad7879-spi. config TOUCHSCREEN_ADC tristate "Generic ADC based resistive touchscreen" depends on IIO select IIO_BUFFER select IIO_BUFFER_CB help Say Y here if you want to use the generic ADC resistive touchscreen driver. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called resistive-adc-touch.ko. config TOUCHSCREEN_APPLE_Z2 tristate "Apple Z2 touchscreens" depends on SPI && (ARCH_APPLE || COMPILE_TEST) help Say Y here if you have an ARM Apple device with a touchscreen or a touchbar. If unsure, say N. To compile this driver as a module, choose M here: the module will be called apple_z2. config TOUCHSCREEN_AR1021_I2C tristate "Microchip AR1020/1021 i2c touchscreen" depends on I2C && OF help Say Y here if you have the Microchip AR1020 or AR1021 touchscreen controller chip in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called ar1021_i2c. config TOUCHSCREEN_ATMEL_MXT tristate "Atmel mXT I2C Touchscreen" depends on I2C select FW_LOADER help Say Y here if you have Atmel mXT series I2C touchscreen, such as AT42QT602240/ATMXT224, connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called atmel_mxt_ts. config TOUCHSCREEN_ATMEL_MXT_T37 bool "Support T37 Diagnostic Data" depends on TOUCHSCREEN_ATMEL_MXT depends on VIDEO_DEV=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_DEV=m) select VIDEOBUF2_VMALLOC help Say Y here if you want support to output data from the T37 Diagnostic Data object using a V4L device. config TOUCHSCREEN_AUO_PIXCIR tristate "AUO in-cell touchscreen using Pixcir ICs" depends on I2C depends on GPIOLIB || COMPILE_TEST help Say Y here if you have a AUO display with in-cell touchscreen using Pixcir ICs. If unsure, say N. To compile this driver as a module, choose M here: the module will be called auo-pixcir-ts. config TOUCHSCREEN_BU21013 tristate "BU21013 based touch panel controllers" depends on I2C help Say Y here if you have a bu21013 touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called bu21013_ts. config TOUCHSCREEN_BU21029 tristate "Rohm BU21029 based touch panel controllers" depends on I2C help Say Y here if you have a Rohm BU21029 touchscreen controller connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called bu21029_ts. config TOUCHSCREEN_CHIPONE_ICN8318 tristate "chipone icn8318 touchscreen controller" depends on GPIOLIB || COMPILE_TEST depends on I2C depends on OF help Say Y here if you have a ChipOne icn8318 based I2C touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called chipone_icn8318. config TOUCHSCREEN_CHIPONE_ICN8505 tristate "chipone icn8505 touchscreen controller" depends on I2C && ACPI help Say Y here if you have a ChipOne icn8505 based I2C touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called chipone_icn8505. config TOUCHSCREEN_CY8CTMA140 tristate "cy8ctma140 touchscreen" depends on I2C help Say Y here if you have a Cypress CY8CTMA140 capacitive touchscreen also just known as "TMA140" If unsure, say N. To compile this driver as a module, choose M here: the module will be called cy8ctma140. config TOUCHSCREEN_CY8CTMG110 tristate "cy8ctmg110 touchscreen" depends on I2C depends on GPIOLIB || COMPILE_TEST help Say Y here if you have a cy8ctmg110 capacitive touchscreen on an AAVA device. If unsure, say N. To compile this driver as a module, choose M here: the module will be called cy8ctmg110_ts. config TOUCHSCREEN_CYTTSP_CORE tristate "Cypress TTSP touchscreen" help Say Y here if you have a touchscreen using controller from the Cypress TrueTouch(tm) Standard Product family connected to your system. You will also need to select appropriate bus connection below. If unsure, say N. To compile this driver as a module, choose M here: the module will be called cyttsp_core. config TOUCHSCREEN_CYTTSP_I2C tristate "support I2C bus connection" depends on TOUCHSCREEN_CYTTSP_CORE && I2C help Say Y here if the touchscreen is connected via I2C bus. To compile this driver as a module, choose M here: the module will be called cyttsp_i2c. config TOUCHSCREEN_CYTTSP_SPI tristate "support SPI bus connection" depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER help Say Y here if the touchscreen is connected via SPI bus. To compile this driver as a module, choose M here: the module will be called cyttsp_spi. config TOUCHSCREEN_CYTTSP5 tristate "Cypress TrueTouch Gen5 Touchscreen Driver" depends on I2C select REGMAP_I2C select CRC_ITU_T help Driver for Parade TrueTouch Standard Product Generation 5 touchscreen controllers. I2C bus interface support only. Say Y here if you have a Cypress Gen5 touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called cyttsp5. config TOUCHSCREEN_DA9034 tristate "Touchscreen support for Dialog Semiconductor DA9034" depends on PMIC_DA903X default y help Say Y here to enable the support for the touchscreen found on Dialog Semiconductor DA9034 PMIC. If unsure, say N. To compile this driver as a module, choose M here: the module will be called da9034-ts. config TOUCHSCREEN_DA9052 tristate "Dialog DA9052/DA9053 TSI" depends on PMIC_DA9052 help Say Y here to support the touchscreen found on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs. If unsure, say N. To compile this driver as a module, choose M here: the module will be called da9052_tsi. config TOUCHSCREEN_DYNAPRO tristate "Dynapro serial touchscreen" select SERIO help Say Y here if you have a Dynapro serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called dynapro. config TOUCHSCREEN_HAMPSHIRE tristate "Hampshire serial touchscreen" select SERIO help Say Y here if you have a Hampshire serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hampshire. config TOUCHSCREEN_EETI tristate "EETI touchscreen panel support" depends on I2C help Say Y here to enable support for I2C connected EETI touch panels. To compile this driver as a module, choose M here: the module will be called eeti_ts. config TOUCHSCREEN_EGALAX tristate "EETI eGalax multi-touch panel support" depends on I2C && OF help Say Y here to enable support for I2C connected EETI eGalax multi-touch panels. To compile this driver as a module, choose M here: the module will be called egalax_ts. config TOUCHSCREEN_EGALAX_SERIAL tristate "EETI eGalax serial touchscreen" select SERIO help Say Y here to enable support for serial connected EETI eGalax touch panels. To compile this driver as a module, choose M here: the module will be called egalax_ts_serial. config TOUCHSCREEN_EXC3000 tristate "EETI EXC3000 multi-touch panel support" depends on I2C help Say Y here to enable support for I2C connected EETI EXC3000 multi-touch panels. To compile this driver as a module, choose M here: the module will be called exc3000. config TOUCHSCREEN_FUJITSU tristate "Fujitsu serial touchscreen" select SERIO help Say Y here if you have the Fujitsu touchscreen (such as one installed in Lifebook P series laptop) connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called fujitsu-ts. config TOUCHSCREEN_GOODIX tristate "Goodix I2C touchscreen" depends on I2C depends on GPIOLIB || COMPILE_TEST help Say Y here if you have the Goodix touchscreen (such as one installed in Onda v975w tablets) connected to your system. It also supports 5-finger chip models, which can be found on ARM tablets, like Wexler TAB7200 and MSI Primo73. If unsure, say N. To compile this driver as a module, choose M here: the module will be called goodix. config TOUCHSCREEN_GOODIX_BERLIN_CORE tristate config TOUCHSCREEN_GOODIX_BERLIN_I2C tristate "Goodix Berlin I2C touchscreen" depends on I2C select REGMAP_I2C select TOUCHSCREEN_GOODIX_BERLIN_CORE help Say Y here if you have a Goodix Berlin IC connected to your system via I2C. If unsure, say N. To compile this driver as a module, choose M here: the module will be called goodix_berlin_i2c. config TOUCHSCREEN_GOODIX_BERLIN_SPI tristate "Goodix Berlin SPI touchscreen" depends on SPI_MASTER select REGMAP select TOUCHSCREEN_GOODIX_BERLIN_CORE help Say Y here if you have a Goodix Berlin IC connected to your system via SPI. If unsure, say N. To compile this driver as a module, choose M here: the module will be called goodix_berlin_spi. config TOUCHSCREEN_HIDEEP tristate "HiDeep Touch IC" depends on I2C select REGMAP_I2C help Say Y here if you have a touchscreen using HiDeep. If unsure, say N. To compile this driver as a module, choose M here : the module will be called hideep_ts. config TOUCHSCREEN_HIMAX_HX852X tristate "Himax HX852x(ES) touchscreen" depends on I2C help Say Y here if you have a Himax HX852x(ES) touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called himax_hx852x. config TOUCHSCREEN_HYCON_HY46XX tristate "Hycon hy46xx touchscreen support" depends on I2C select REGMAP_I2C help Say Y here if you have a touchscreen using Hycon hy46xx If unsure, say N. To compile this driver as a module, choose M here: the module will be called hycon-hy46xx. config TOUCHSCREEN_HYNITRON_CSTXXX tristate "Hynitron touchscreen support" depends on I2C help Say Y here if you have a touchscreen using a Hynitron touchscreen controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hynitron-cstxxx. config TOUCHSCREEN_HYNITRON_CST816X tristate "Hynitron CST816x touchscreen" depends on I2C help Say Y here if you have a touchscreen using a Hynitron CST816x series touchscreen controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called hynitron-cst816x. config TOUCHSCREEN_ILI210X tristate "Ilitek ILI210X based touchscreen" depends on I2C select CRC_CCITT help Say Y here if you have a ILI210X based touchscreen controller. This driver supports models ILI2102, ILI2102s, ILI2103, ILI2103s and ILI2105. Such kind of chipsets can be found in Amazon Kindle Fire touchscreens.