648 lines · 16.3 KB · C
RawDownload
/* * Copyright (C) 2004, 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * Vineetg: March 2009 (Supporting 2 levels of Interrupts) *  Stack switching code can no longer reliably rely on the fact that *  if we are NOT in user mode, stack is switched to kernel mode. *  e.g. L2 IRQ interrupted a L1 ISR which had not yet completed *  it's prologue including stack switching from user mode * * Vineetg: Aug 28th 2008: Bug #94984 *  -Zero Overhead Loop Context shd be cleared when entering IRQ/EXcp/Trap *   Normally CPU does this automatically, however when doing FAKE rtie, *   we also need to explicitly do this. The problem in macros *   FAKE_RET_FROM_EXCPN and FAKE_RET_FROM_EXCPN_LOCK_IRQ was that this bit *   was being "CLEARED" rather then "SET". Actually "SET" clears ZOL context * * Vineetg: May 5th 2008 *  -Modified CALLEE_REG save/restore macros to handle the fact that *      r25 contains the kernel current task ptr *  - Defined Stack Switching Macro to be reused in all intr/excp hdlrs *  - Shaved off 11 instructions from RESTORE_ALL_INT1 by using the *      address Write back load ld.ab instead of seperate ld/add instn * * Amit Bhor, Sameer Dhavale: Codito Technologies 2004 */ #ifndef __ASM_ARC_ENTRY_H#define __ASM_ARC_ENTRY_H #ifdef __ASSEMBLY__#include <asm/unistd.h>		/* For NR_syscalls defination */#include <asm/asm-offsets.h>#include <asm/arcregs.h>#include <asm/ptrace.h>#include <asm/processor.h>	/* For VMALLOC_START */#include <asm/thread_info.h>	/* For THREAD_SIZE */#include <asm/mmu.h> /* Note on the LD/ST addr modes with addr reg wback * * LD.a same as LD.aw * * LD.a    reg1, [reg2, x]  => Pre Incr *      Eff Addr for load = [reg2 + x] * * LD.ab   reg1, [reg2, x]  => Post Incr *      Eff Addr for load = [reg2] */ .macro PUSH reg	st.a	\reg, [sp, -4].endm .macro PUSHAX aux	lr	r9, [\aux]	PUSH	r9.endm .macro POP reg	ld.ab	\reg, [sp, 4].endm .macro POPAX aux	POP	r9	sr	r9, [\aux].endm /*-------------------------------------------------------------- * Helpers to save/restore Scratch Regs: * used by Interrupt/Exception Prologue/Epilogue *-------------------------------------------------------------*/.macro  SAVE_R0_TO_R12	PUSH	r0	PUSH	r1	PUSH	r2	PUSH	r3	PUSH	r4	PUSH	r5	PUSH	r6	PUSH	r7	PUSH	r8	PUSH	r9	PUSH	r10	PUSH	r11	PUSH	r12.endm .macro RESTORE_R12_TO_R0	POP	r12	POP	r11	POP	r10	POP	r9	POP	r8	POP	r7	POP	r6	POP	r5	POP	r4	POP	r3	POP	r2	POP	r1	POP	r0 #ifdef CONFIG_ARC_CURR_IN_REG	ld	r25, [sp, 12]#endif.endm /*-------------------------------------------------------------- * Helpers to save/restore callee-saved regs: * used by several macros below *-------------------------------------------------------------*/.macro SAVE_R13_TO_R24	PUSH	r13	PUSH	r14	PUSH	r15	PUSH	r16	PUSH	r17	PUSH	r18	PUSH	r19	PUSH	r20	PUSH	r21	PUSH	r22	PUSH	r23	PUSH	r24.endm .macro RESTORE_R24_TO_R13	POP	r24	POP	r23	POP	r22	POP	r21	POP	r20	POP	r19	POP	r18	POP	r17	POP	r16	POP	r15	POP	r14	POP	r13.endm #define OFF_USER_R25_FROM_R24	(SZ_CALLEE_REGS + SZ_PT_REGS - 8)/4 /*-------------------------------------------------------------- * Collect User Mode callee regs as struct callee_regs - needed by * fork/do_signal/unaligned-access-emulation. * (By default only scratch regs are saved on entry to kernel) * * Special handling for r25 if used for caching Task Pointer. * It would have been saved in task->thread.user_r25 already, but to keep * the interface same it is copied into regular r25 placeholder in * struct callee_regs. *-------------------------------------------------------------*/.macro SAVE_CALLEE_SAVED_USER 	SAVE_R13_TO_R24 #ifdef CONFIG_ARC_CURR_IN_REG	; Retrieve orig r25 and save it on stack	ld.as   r12, [sp, OFF_USER_R25_FROM_R24]	st.a    r12, [sp, -4]#else	PUSH	r25#endif .endm /*-------------------------------------------------------------- * Save kernel Mode callee regs at the time of Contect Switch. * * Special handling for r25 if used for caching Task Pointer. * Kernel simply skips saving it since it will be loaded with * incoming task pointer anyways *-------------------------------------------------------------*/.macro SAVE_CALLEE_SAVED_KERNEL 	SAVE_R13_TO_R24 #ifdef CONFIG_ARC_CURR_IN_REG	sub     sp, sp, 4#else	PUSH	r25#endif.endm /*-------------------------------------------------------------- * Opposite of SAVE_CALLEE_SAVED_KERNEL *-------------------------------------------------------------*/.macro RESTORE_CALLEE_SAVED_KERNEL #ifdef CONFIG_ARC_CURR_IN_REG	add     sp, sp, 4  /* skip usual r25 placeholder */#else	POP	r25#endif	RESTORE_R24_TO_R13.endm /*-------------------------------------------------------------- * Opposite of SAVE_CALLEE_SAVED_USER * * ptrace tracer or unaligned-access fixup might have changed a user mode * callee reg which is saved back to usual r25 storage location *-------------------------------------------------------------*/.macro RESTORE_CALLEE_SAVED_USER #ifdef CONFIG_ARC_CURR_IN_REG	ld.ab   r12, [sp, 4]	st.as   r12, [sp, OFF_USER_R25_FROM_R24]#else	POP	r25#endif	RESTORE_R24_TO_R13.endm /*-------------------------------------------------------------- * Super FAST Restore callee saved regs by simply re-adjusting SP *-------------------------------------------------------------*/.macro DISCARD_CALLEE_SAVED_USER	add     sp, sp, SZ_CALLEE_REGS.endm /*------------------------------------------------------------- * given a tsk struct, get to the base of it's kernel mode stack * tsk->thread_info is really a PAGE, whose bottom hoists stack * which grows upwards towards thread_info *------------------------------------------------------------*/ .macro GET_TSK_STACK_BASE tsk, out 	/* Get task->thread_info (this is essentially start of a PAGE) */	ld  \out, [\tsk, TASK_THREAD_INFO] 	/* Go to end of page where stack begins (grows upwards) */	add2 \out, \out, (THREAD_SIZE)/4 .endm /*-------------------------------------------------------------- * Switch to Kernel Mode stack if SP points to User Mode stack * * Entry   : r9 contains pre-IRQ/exception/trap status32 * Exit    : SP is set to kernel mode stack pointer *           If CURR_IN_REG, r25 set to "current" task pointer * Clobbers: r9 *-------------------------------------------------------------*/ .macro SWITCH_TO_KERNEL_STK 	/* User Mode when this happened ? Yes: Proceed to switch stack */	bbit1   r9, STATUS_U_BIT, 88f 	/* OK we were already in kernel mode when this event happened, thus can	 * assume SP is kernel mode SP. _NO_ need to do any stack switching	 */ #ifdef CONFIG_ARC_COMPACT_IRQ_LEVELS	/* However....	 * If Level 2 Interrupts enabled, we may end up with a corner case:	 * 1. User Task executing	 * 2. L1 IRQ taken, ISR starts (CPU auto-switched to KERNEL mode)	 * 3. But before it could switch SP from USER to KERNEL stack	 *      a L2 IRQ "Interrupts" L1	 * Thay way although L2 IRQ happened in Kernel mode, stack is still	 * not switched.	 * To handle this, we may need to switch stack even if in kernel mode	 * provided SP has values in range of USER mode stack ( < 0x7000_0000 )	 */	brlo sp, VMALLOC_START, 88f 	/* TODO: vineetg:	 * We need to be a bit more cautious here. What if a kernel bug in	 * L1 ISR, caused SP to go whaco (some small value which looks like	 * USER stk) and then we take L2 ISR.	 * Above brlo alone would treat it as a valid L1-L2 sceanrio	 * instead of shouting alound	 * The only feasible way is to make sure this L2 happened in	 * L1 prelogue ONLY i.e. ilink2 is less than a pre-set marker in	 * L1 ISR before it switches stack	 */ #endif 	/* Save Pre Intr/Exception KERNEL MODE SP on kernel stack	 * safe-keeping not really needed, but it keeps the epilogue code	 * (SP restore) simpler/uniform.	 */	b.d	66f	mov	r9, sp 88: /*------Intr/Ecxp happened in user mode, "switch" stack ------ */ 	GET_CURR_TASK_ON_CPU   r9 	/* With current tsk in r9, get it's kernel mode stack base */	GET_TSK_STACK_BASE  r9, r9 66:#ifdef CONFIG_ARC_CURR_IN_REG	/*	 * Treat r25 as scratch reg, save it on stack first	 * Load it with current task pointer	 */	st	r25, [r9, -4]	GET_CURR_TASK_ON_CPU   r25#endif 	/* Save Pre Intr/Exception User SP on kernel stack */	st.a    sp, [r9, -16]	; Make room for orig_r0, ECR, user_r25 	/* CAUTION:	 * SP should be set at the very end when we are done with everything	 * In case of 2 levels of interrupt we depend on value of SP to assume	 * that everything else is done (loading r25 etc)	 */ 	/* set SP to point to kernel mode stack */	mov sp, r9 	/* ----- Stack Switched to kernel Mode, Now save REG FILE ----- */ .endm /*------------------------------------------------------------ * "FAKE" a rtie to return from CPU Exception context * This is to re-enable Exceptions within exception * Look at EV_ProtV to see how this is actually used *-------------------------------------------------------------*/ .macro FAKE_RET_FROM_EXCPN  reg 	ld  \reg, [sp, PT_status32]	bic  \reg, \reg, (STATUS_U_MASK|STATUS_DE_MASK)	bset \reg, \reg, STATUS_L_BIT	sr  \reg, [erstatus]	mov \reg, 55f	sr  \reg, [eret] 	rtie55:.endm /* * @reg [OUT] &thread_info of "current" */.macro GET_CURR_THR_INFO_FROM_SP  reg	bic \reg, sp, (THREAD_SIZE - 1).endm /* * @reg [OUT] thread_info->flags of "current" */.macro GET_CURR_THR_INFO_FLAGS  reg	GET_CURR_THR_INFO_FROM_SP  \reg	ld  \reg, [\reg, THREAD_INFO_FLAGS].endm /*-------------------------------------------------------------- * For early Exception Prologue, a core reg is temporarily needed to * code the rest of prolog (stack switching). This is done by stashing * it to memory (non-SMP case) or SCRATCH0 Aux Reg (SMP). * * Before saving the full regfile - this reg is restored back, only * to be saved again on kernel mode stack, as part of pt_regs. *-------------------------------------------------------------*/.macro EXCPN_PROLOG_FREEUP_REG	reg#ifdef CONFIG_SMP	sr  \reg, [ARC_REG_SCRATCH_DATA0]#else	st  \reg, [@ex_saved_reg1]#endif.endm .macro EXCPN_PROLOG_RESTORE_REG	reg#ifdef CONFIG_SMP	lr  \reg, [ARC_REG_SCRATCH_DATA0]#else	ld  \reg, [@ex_saved_reg1]#endif.endm /*-------------------------------------------------------------- * Exception Entry prologue * -Switches stack to K mode (if not already) * -Saves the register file * * After this it is safe to call the "C" handlers *-------------------------------------------------------------*/.macro EXCEPTION_PROLOGUE 	/* Need at least 1 reg to code the early exception prologue */	EXCPN_PROLOG_FREEUP_REG r9 	/* U/K mode at time of exception (stack not switched if already K) */	lr  r9, [erstatus] 	/* ARC700 doesn't provide auto-stack switching */	SWITCH_TO_KERNEL_STK 	/* save the regfile */	SAVE_ALL_SYS.endm /*-------------------------------------------------------------- * Save all registers used by Exceptions (TLB Miss, Prot-V, Mem err etc) * Requires SP to be already switched to kernel mode Stack * sp points to the next free element on the stack at exit of this macro. * Registers are pushed / popped in the order defined in struct ptregs * in asm/ptrace.h * Note that syscalls are implemented via TRAP which is also a exception * from CPU's point of view *-------------------------------------------------------------*/.macro SAVE_ALL_SYS 	lr	r9, [ecr]	st      r9, [sp, 8]    /* ECR */	st      r0, [sp, 4]    /* orig_r0, needed only for sys calls */ 	/* Restore r9 used to code the early prologue */	EXCPN_PROLOG_RESTORE_REG  r9 	SAVE_R0_TO_R12	PUSH	gp	PUSH	fp	PUSH	blink	PUSHAX	eret	PUSHAX	erstatus	PUSH	lp_count	PUSHAX	lp_end	PUSHAX	lp_start	PUSHAX	erbta.endm /*-------------------------------------------------------------- * Restore all registers used by system call or Exceptions * SP should always be pointing to the next free stack element * when entering this macro. * * NOTE: * * It is recommended that lp_count/ilink1/ilink2 not be used as a dest reg * for memory load operations. If used in that way interrupts are deffered * by hardware and that is not good. *-------------------------------------------------------------*/.macro RESTORE_ALL_SYS	POPAX	erbta	POPAX	lp_start	POPAX	lp_end 	POP	r9	mov	lp_count, r9	;LD to lp_count is not allowed 	POPAX	erstatus	POPAX	eret	POP	blink	POP	fp	POP	gp	RESTORE_R12_TO_R0 	ld  sp, [sp] /* restore original sp */	/* orig_r0, ECR, user_r25 skipped automatically */.endm  /*-------------------------------------------------------------- * Save all registers used by interrupt handlers. *-------------------------------------------------------------*/.macro SAVE_ALL_INT1 	/* restore original r9 to be saved as part of reg-file */#ifdef CONFIG_SMP	lr  r9, [ARC_REG_SCRATCH_DATA0]#else	ld  r9, [@int1_saved_reg]#endif 	/* now we are ready to save the remaining context :) */	st      event_IRQ1, [sp, 8]    /* Dummy ECR */	st      0, [sp, 4]    /* orig_r0 , N/A for IRQ */ 	SAVE_R0_TO_R12	PUSH	gp	PUSH	fp	PUSH	blink	PUSH	ilink1	PUSHAX	status32_l1	PUSH	lp_count	PUSHAX	lp_end	PUSHAX	lp_start	PUSHAX	bta_l1.endm .macro SAVE_ALL_INT2 	/* TODO-vineetg: SMP we can't use global nor can we use	*   SCRATCH0 as we do for int1 because while int1 is using

Lines 1–500 of 648.

Keyboard shortcuts

General

Show keyboard shortcuts
?
Focus the current search
/

Issues and pull requests

Open filters
f

Issues, pull requests and Inbox

Select next item
j↓
Select previous item
k↑
Open selected item
Enter
Dismiss filters or clear selection
Esc

Repository code

Go to file
t