## Config file for ktest.pl## Note, all paths must be absolute# # Options set in the beginning of the file are considered to be# default options. These options can be overriden by test specific# options, with the following exceptions:## LOG_FILE# CLEAR_LOG# POWEROFF_ON_SUCCESS# REBOOT_ON_SUCCESS## Test specific options are set after the label:## TEST_START## The options after a TEST_START label are specific to that test.# Each TEST_START label will set up a new test. If you want to# perform a test more than once, you can add the ITERATE label# to it followed by the number of times you want that test# to iterate. If the ITERATE is left off, the test will only# be performed once.## TEST_START ITERATE 10## You can skip a test by adding SKIP (before or after the ITERATE# and number)## TEST_START SKIP## TEST_START SKIP ITERATE 10## TEST_START ITERATE 10 SKIP## The SKIP label causes the options and the test itself to be ignored.# This is useful to set up several different tests in one config file, and# only enabling the ones you want to use for a current test run.## You can add default options anywhere in the file as well# with the DEFAULTS tag. This allows you to have default options# after the test options to keep the test options at the top# of the file. You can even place the DEFAULTS tag between# test cases (but not in the middle of a single test case)## TEST_START# MIN_CONFIG = /home/test/config-test1## DEFAULTS# MIN_CONFIG = /home/test/config-default## TEST_START ITERATE 10## The above will run the first test with MIN_CONFIG set to# /home/test/config-test-1. Then 10 tests will be executed# with MIN_CONFIG with /home/test/config-default.## You can also disable defaults with the SKIP option## DEFAULTS SKIP# MIN_CONFIG = /home/test/config-use-sometimes## DEFAULTS# MIN_CONFIG = /home/test/config-most-times## The above will ignore the first MIN_CONFIG. If you want to# use the first MIN_CONFIG, remove the SKIP from the first# DEFAULTS tag and add it to the second. Be careful, options# may only be declared once per test or default. If you have# the same option name under the same test or as default# ktest will fail to execute, and no tests will run.## DEFAULTS OVERRIDE## Options defined in the DEFAULTS section can not be duplicated# even if they are defined in two different DEFAULT sections.# This is done to catch mistakes where an option is added but# the previous option was forgotten about and not commented.## The OVERRIDE keyword can be added to a section to allow this# section to override other DEFAULT sections values that have# been defined previously. It will only override options that# have been defined before its use. Options defined later# in a non override section will still error. The same option# can not be defined in the same section even if that section# is marked OVERRIDE.#### Both TEST_START and DEFAULTS sections can also have the IF keyword# The value after the IF must evaluate into a 0 or non 0 positive# integer, and can use the config variables (explained below).## DEFAULTS IF ${IS_X86_32}## The above will process the DEFAULTS section if the config# variable IS_X86_32 evaluates to a non zero positive integer# otherwise if it evaluates to zero, it will act the same# as if the SKIP keyword was used.## The ELSE keyword can be used directly after a section with# a IF statement.## TEST_START IF ${RUN_NET_TESTS}# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-network## ELSE## BUILD_TYPE = useconfig:${CONFIG_DIR}/config-normal### The ELSE keyword can also contain an IF statement to allow multiple# if then else sections. But all the sections must be either# DEFAULT or TEST_START, they can not be a mixture.## TEST_START IF ${RUN_NET_TESTS}# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-network## ELSE IF ${RUN_DISK_TESTS}# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-tests## ELSE IF ${RUN_CPU_TESTS}# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-cpu## ELSE# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-network## The if statement may also have comparisons that will and for# == and !=, strings may be used for both sides.## BOX_TYPE := x86_32## DEFAULTS IF ${BOX_TYPE} == x86_32# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-32# ELSE# BUILD_TYPE = useconfig:${CONFIG_DIR}/config-64## The DEFINED keyword can be used by the IF statements too.# It returns true if the given config variable or option has been defined# or false otherwise.## # DEFAULTS IF DEFINED USE_CC# CC := ${USE_CC}# ELSE# CC := gcc### As well as NOT DEFINED.## DEFAULTS IF NOT DEFINED MAKE_CMD# MAKE_CMD := make ARCH=x86### And/or ops (&&,||) may also be used to make complex conditionals.## TEST_START IF (DEFINED ALL_TESTS || ${MYTEST} == boottest) && ${MACHINE} == gandalf## Notice the use of parentheses. Without any parentheses the above would be# processed the same as:## TEST_START IF DEFINED ALL_TESTS || (${MYTEST} == boottest && ${MACHINE} == gandalf)#### INCLUDE file## The INCLUDE keyword may be used in DEFAULT sections. This will# read another config file and process that file as well. The included# file can include other files, add new test cases or default# statements. Config variables will be passed to these files and changes# to config variables will be seen by top level config files. Including# a file is processed just like the contents of the file was cut and pasted# into the top level file, except, that include files that end with# TEST_START sections will have that section ended at the end of# the include file. That is, an included file is included followed# by another DEFAULT keyword.## Unlike other files referenced in this config, the file path does not need# to be absolute. If the file does not start with '/', then the directory# that the current config file was located in is used. If no config by the# given name is found there, then the current directory is searched.## INCLUDE myfile# DEFAULT## is the same as:## INCLUDE myfile## Note, if the include file does not contain a full path, the file is# searched first by the location of the original include file, and then# by the location that ktest.pl was executed in.# #### Config variables ###### This config file can also contain "config variables".# These are assigned with ":=" instead of the ktest option# assigment "=".## The difference between ktest options and config variables# is that config variables can be used multiple times,# where each instance will override the previous instance.# And that they only live at time of processing this config.## The advantage to config variables are that they can be used# by any option or any other config variables to define thing# that you may use over and over again in the options.## For example:## USER := root# TARGET := mybox# TEST_CASE := ssh ${USER}@${TARGET} /path/to/my/test## TEST_START# MIN_CONFIG = config1# TEST = ${TEST_CASE}## TEST_START# MIN_CONFIG = config2# TEST = ${TEST_CASE}## TEST_CASE := ssh ${USER}@${TARGET} /path/to/my/test2## TEST_START# MIN_CONFIG = config1# TEST = ${TEST_CASE}## TEST_START# MIN_CONFIG = config2# TEST = ${TEST_CASE}## TEST_DIR := /home/me/test## BUILD_DIR = ${TEST_DIR}/linux.git# OUTPUT_DIR = ${TEST_DIR}/test## Note, the config variables are evaluated immediately, thus# updating TARGET after TEST_CASE has been assigned does nothing# to TEST_CASE.## As shown in the example, to evaluate a config variable, you# use the ${X} convention. Simple $X will not work.## If the config variable does not exist, the ${X} will not# be evaluated. Thus:## MAKE_CMD = PATH=/mypath:${PATH} make## If PATH is not a config variable, then the ${PATH} in# the MAKE_CMD option will be evaluated by the shell when# the MAKE_CMD option is passed into shell processing. #### Using options in other options ###### Options that are defined in the config file may also be used# by other options. All options are evaulated at time of# use (except that config variables are evaluated at config# processing time).## If an ktest option is used within another option, instead of# typing it again in that option you can simply use the option# just like you can config variables.## MACHINE = mybox## TEST = ssh root@${MACHINE} /path/to/test## The option will be used per test case. Thus:## TEST_TYPE = test# TEST = ssh root@{MACHINE}## TEST_START# MACHINE = box1## TEST_START# MACHINE = box2## For both test cases, MACHINE will be evaluated at the time# of the test case. The first test will run ssh root@box1# and the second will run ssh root@box2. #### Mandatory Default Options #### # These options must be in the default section, although most# may be overridden by test options. # The machine hostname that you will test#MACHINE = target # The box is expected to have ssh on normal bootup, provide the user# (most likely root, since you need privileged operations)#SSH_USER = root # The directory that contains the Linux source code#BUILD_DIR = /home/test/linux.git # The directory that the objects will be built# (can not be same as BUILD_DIR)#OUTPUT_DIR = /home/test/build/target # The location of the compiled file to copy to the target# (relative to OUTPUT_DIR)#BUILD_TARGET = arch/x86/boot/bzImage # The place to put your image on the test machine#TARGET_IMAGE = /boot/vmlinuz-test # A script or command to reboot the box## Here is a digital loggers power switch example#POWER_CYCLE = wget --no-proxy -O /dev/null -q --auth-no-challenge 'http://admin:admin@power/outlet?5=CCL'## Here is an example to reboot a virtual box on the current host# with the name "Guest".#POWER_CYCLE = virsh destroy Guest; sleep 5; virsh start Guest # The script or command that reads the console## If you use ttywatch server, something like the following would work.#CONSOLE = nc -d localhost 3001## For a virtual machine with guest name "Guest".#CONSOLE = virsh console Guest # Signal to send to kill console.# ktest.pl will create a child process to monitor the console.# When the console is finished, ktest will kill the child process# with this signal.# (default INT)#CLOSE_CONSOLE_SIGNAL = HUP # Required version ending to differentiate the test# from other linux builds on the system.#LOCALVERSION = -test # For REBOOT_TYPE = grub2, you must specify where the grub.cfg# file is. This is the file that is searched to find the menu# option to boot to with GRUB_REBOOT#GRUB_FILE = /boot/grub2/grub.cfg # The tool for REBOOT_TYPE = grub2 to set the next reboot kernel# to boot into (one shot mode).# (default grub2_reboot)#GRUB_REBOOT = grub2_reboot # The grub title name for the test kernel to boot# (Only mandatory if REBOOT_TYPE = grub or grub2)## Note, ktest.pl will not update the grub menu.lst, you need to# manually add an option for the test. ktest.pl will search# the grub menu.lst for this option to find what kernel to# reboot into.## For example, if in the /boot/grub/menu.lst the test kernel title has:# title Test Kernel# kernel vmlinuz-test## For grub2, a search of top level "menuentry"s are done. No# submenu is searched. The menu is found by searching for the# contents of GRUB_MENU in the line that starts with "menuentry".# You may want to include the quotes around the option. For example:# for: menuentry 'Test Kernel'# do a: GRUB_MENU = 'Test Kernel'# For customizing, add your entry in /etc/grub.d/40_custom.##GRUB_MENU = Test Kernel # For REBOOT_TYPE = syslinux, the name of the syslinux executable# (on the target) to use to set up the next reboot to boot the# test kernel.# (default extlinux)#SYSLINUX = syslinux # For REBOOT_TYPE = syslinux, the path that is passed to to the# syslinux command where syslinux is installed.# (default /boot/extlinux)#SYSLINUX_PATH = /boot/syslinux # For REBOOT_TYPE = syslinux, the syslinux label that references the# test kernel in the syslinux config file.# (default undefined)#SYSLINUX_LABEL = "test-kernel" # A script to reboot the target into the test kernel# This and SWITCH_TO_TEST are about the same, except# SWITCH_TO_TEST is run even for REBOOT_TYPE = grub.# This may be left undefined.# (default undefined)#REBOOT_SCRIPT = #### Optional Config Options (all have defaults) #### # Start a test setup. If you leave this off, all options# will be default and the test will run once.# This is a label and not really an option (it takes no value).# You can append ITERATE and a number after it to iterate the# test a number of times, or SKIP to ignore this test.##TEST_START#TEST_START ITERATE 5#TEST_START SKIP # Have the following options as default again. Used after tests# have already been defined by TEST_START. Optionally, you can# just define all default options before the first TEST_START# and you do not need this option.## This is a label and not really an option (it takes no value).# You can append SKIP to this label and the options within this# section will be ignored.## DEFAULTS# DEFAULTS SKIP # If you want to execute some command before the first test runs# you can set this option. Note, it can be set as a default option# or an option in the first test case. All other test cases will# ignore it. If both the default and first test have this option# set, then the first test will take precedence.## default (undefined)#PRE_KTEST = ${SSH} ~/set_up_test # If you want to execute some command after all the tests have# completed, you can set this option. Note, it can be set as a# default or any test case can override it. If multiple test cases# set this option, then the last test case that set it will take# precedence## default (undefined)#POST_KTEST = ${SSH} ~/dismantle_test # The default test type (default test)# The test types may be:# build - only build the kernel, do nothing else# install - build and install, but do nothing else (does not reboot)# boot - build, install, and boot the kernel# test - build, boot and if TEST is set, run the test script# (If TEST is not set, it defaults back to boot)# bisect - Perform a bisect on the kernel (see BISECT_TYPE below)# patchcheck - Do a test on a series of commits in git (see PATCHCHECK below)#TEST_TYPE = test # Test to run if there is a successful boot and TEST_TYPE is test.# Must exit with 0 on success and non zero on error# default (undefined)#TEST = ssh user@machine /root/run_test # The build type is any make config type or special command# (default randconfig)# nobuild - skip the clean and build step# useconfig:/path/to/config - use the given config and run# oldconfig on it.# This option is ignored if TEST_TYPE is patchcheck or bisect#BUILD_TYPE = randconfig # The make command (default make)# If you are building a 32bit x86 on a 64 bit host#MAKE_CMD = CC=i386-gcc AS=i386-as make ARCH=i386 # Any build options for the make of the kernel (not for other makes, like configs)# (default "")#BUILD_OPTIONS = -j20 # If you need to do some special handling before installing# you can add a script with this option.# The environment variable KERNEL_VERSION will be set to the# kernel version that is used.## default (undefined)#PRE_INSTALL = ssh user@target rm -rf '/lib/modules/*-test*' # If you need an initrd, you can add a script or code here to install# it. The environment variable KERNEL_VERSION will be set to the# kernel version that is used. Remember to add the initrd line# to your grub menu.lst file.## Here's a couple of examples to use:#POST_INSTALL = ssh user@target /sbin/mkinitrd --allow-missing -f /boot/initramfs-test.img $KERNEL_VERSION## or on some systems:#POST_INSTALL = ssh user@target /sbin/dracut -f /boot/initramfs-test.img $KERNEL_VERSION # If for some reason you just want to boot the kernel and you do not# want the test to install anything new. For example, you may just want# to boot test the same kernel over and over and do not want to go through# the hassle of installing anything, you can set this option to 1# (default 0)#NO_INSTALL = 1 # If there is a command that you want to run before the individual test# case executes, then you can set this option## default (undefined)Lines 1–500 of 1289. Load more
# # Config file for ktest.pl # # Note, all paths must be absolute # # Options set in the beginning of the file are considered to be # default options. These options can be overriden by test specific # options, with the following exceptions: # # LOG_FILE # CLEAR_LOG # POWEROFF_ON_SUCCESS # REBOOT_ON_SUCCESS # # Test specific options are set after the label: # # TEST_START # # The options after a TEST_START label are specific to that test. # Each TEST_START label will set up a new test. If you want to # perform a test more than once, you can add the ITERATE label # to it followed by the number of times you want that test # to iterate. If the ITERATE is left off, the test will only # be performed once. # # TEST_START ITERATE 10 # # You can skip a test by adding SKIP (before or after the ITERATE # and number) # # TEST_START SKIP # # TEST_START SKIP ITERATE 10 # # TEST_START ITERATE 10 SKIP # # The SKIP label causes the options and the test itself to be ignored. # This is useful to set up several different tests in one config file, and # only enabling the ones you want to use for a current test run. # # You can add default options anywhere in the file as well # with the DEFAULTS tag. This allows you to have default options # after the test options to keep the test options at the top # of the file. You can even place the DEFAULTS tag between # test cases (but not in the middle of a single test case) # # TEST_START # MIN_CONFIG = /home/test/config-test1 # # DEFAULTS # MIN_CONFIG = /home/test/config-default # # TEST_START ITERATE 10 # # The above will run the first test with MIN_CONFIG set to # /home/test/config-test-1. Then 10 tests will be executed # with MIN_CONFIG with /home/test/config-default. # # You can also disable defaults with the SKIP option # # DEFAULTS SKIP # MIN_CONFIG = /home/test/config-use-sometimes # # DEFAULTS # MIN_CONFIG = /home/test/config-most-times # # The above will ignore the first MIN_CONFIG. If you want to # use the first MIN_CONFIG, remove the SKIP from the first # DEFAULTS tag and add it to the second. Be careful, options # may only be declared once per test or default. If you have # the same option name under the same test or as default # ktest will fail to execute, and no tests will run. # # DEFAULTS OVERRIDE # # Options defined in the DEFAULTS section can not be duplicated # even if they are defined in two different DEFAULT sections. # This is done to catch mistakes where an option is added but # the previous option was forgotten about and not commented. # # The OVERRIDE keyword can be added to a section to allow this # section to override other DEFAULT sections values that have # been defined previously. It will only override options that # have been defined before its use. Options defined later # in a non override section will still error. The same option # can not be defined in the same section even if that section # is marked OVERRIDE. # # # # Both TEST_START and DEFAULTS sections can also have the IF keyword # The value after the IF must evaluate into a 0 or non 0 positive # integer, and can use the config variables (explained below). # # DEFAULTS IF ${IS_X86_32} # # The above will process the DEFAULTS section if the config # variable IS_X86_32 evaluates to a non zero positive integer # otherwise if it evaluates to zero, it will act the same # as if the SKIP keyword was used. # # The ELSE keyword can be used directly after a section with # a IF statement. # # TEST_START IF ${RUN_NET_TESTS} # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-network # # ELSE # # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-normal # # # The ELSE keyword can also contain an IF statement to allow multiple # if then else sections. But all the sections must be either # DEFAULT or TEST_START, they can not be a mixture. # # TEST_START IF ${RUN_NET_TESTS} # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-network # # ELSE IF ${RUN_DISK_TESTS} # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-tests # # ELSE IF ${RUN_CPU_TESTS} # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-cpu # # ELSE # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-network # # The if statement may also have comparisons that will and for # == and !=, strings may be used for both sides. # # BOX_TYPE := x86_32 # # DEFAULTS IF ${BOX_TYPE} == x86_32 # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-32 # ELSE # BUILD_TYPE = useconfig:${CONFIG_DIR}/config-64 # # The DEFINED keyword can be used by the IF statements too. # It returns true if the given config variable or option has been defined # or false otherwise. # # # DEFAULTS IF DEFINED USE_CC # CC := ${USE_CC} # ELSE # CC := gcc # # # As well as NOT DEFINED. # # DEFAULTS IF NOT DEFINED MAKE_CMD # MAKE_CMD := make ARCH=x86 # # # And/or ops (&&,||) may also be used to make complex conditionals. # # TEST_START IF (DEFINED ALL_TESTS || ${MYTEST} == boottest) && ${MACHINE} == gandalf # # Notice the use of parentheses. Without any parentheses the above would be # processed the same as: # # TEST_START IF DEFINED ALL_TESTS || (${MYTEST} == boottest && ${MACHINE} == gandalf) # # # # INCLUDE file # # The INCLUDE keyword may be used in DEFAULT sections. This will # read another config file and process that file as well. The included # file can include other files, add new test cases or default # statements. Config variables will be passed to these files and changes # to config variables will be seen by top level config files. Including # a file is processed just like the contents of the file was cut and pasted # into the top level file, except, that include files that end with # TEST_START sections will have that section ended at the end of # the include file. That is, an included file is included followed # by another DEFAULT keyword. # # Unlike other files referenced in this config, the file path does not need # to be absolute. If the file does not start with '/', then the directory # that the current config file was located in is used. If no config by the # given name is found there, then the current directory is searched. # # INCLUDE myfile # DEFAULT # # is the same as: # # INCLUDE myfile # # Note, if the include file does not contain a full path, the file is # searched first by the location of the original include file, and then # by the location that ktest.pl was executed in. # #### Config variables #### # # This config file can also contain "config variables". # These are assigned with ":=" instead of the ktest option # assigment "=". # # The difference between ktest options and config variables # is that config variables can be used multiple times, # where each instance will override the previous instance. # And that they only live at time of processing this config. # # The advantage to config variables are that they can be used # by any option or any other config variables to define thing # that you may use over and over again in the options. # # For example: # # USER := root # TARGET := mybox # TEST_CASE := ssh ${USER}@${TARGET} /path/to/my/test # # TEST_START # MIN_CONFIG = config1 # TEST = ${TEST_CASE} # # TEST_START # MIN_CONFIG = config2 # TEST = ${TEST_CASE} # # TEST_CASE := ssh ${USER}@${TARGET} /path/to/my/test2 # # TEST_START # MIN_CONFIG = config1 # TEST = ${TEST_CASE} # # TEST_START # MIN_CONFIG = config2 # TEST = ${TEST_CASE} # # TEST_DIR := /home/me/test # # BUILD_DIR = ${TEST_DIR}/linux.git # OUTPUT_DIR = ${TEST_DIR}/test # # Note, the config variables are evaluated immediately, thus # updating TARGET after TEST_CASE has been assigned does nothing # to TEST_CASE. # # As shown in the example, to evaluate a config variable, you # use the ${X} convention. Simple $X will not work. # # If the config variable does not exist, the ${X} will not # be evaluated. Thus: # # MAKE_CMD = PATH=/mypath:${PATH} make # # If PATH is not a config variable, then the ${PATH} in # the MAKE_CMD option will be evaluated by the shell when # the MAKE_CMD option is passed into shell processing. #### Using options in other options #### # # Options that are defined in the config file may also be used # by other options. All options are evaulated at time of # use (except that config variables are evaluated at config # processing time). # # If an ktest option is used within another option, instead of # typing it again in that option you can simply use the option # just like you can config variables. # # MACHINE = mybox # # TEST = ssh root@${MACHINE} /path/to/test # # The option will be used per test case. Thus: # # TEST_TYPE = test # TEST = ssh root@{MACHINE} # # TEST_START # MACHINE = box1 # # TEST_START # MACHINE = box2 # # For both test cases, MACHINE will be evaluated at the time # of the test case. The first test will run ssh root@box1 # and the second will run ssh root@box2. #### Mandatory Default Options #### # These options must be in the default section, although most # may be overridden by test options. # The machine hostname that you will test #MACHINE = target # The box is expected to have ssh on normal bootup, provide the user # (most likely root, since you need privileged operations) #SSH_USER = root # The directory that contains the Linux source code #BUILD_DIR = /home/test/linux.git # The directory that the objects will be built # (can not be same as BUILD_DIR) #OUTPUT_DIR = /home/test/build/target # The location of the compiled file to copy to the target # (relative to OUTPUT_DIR) #BUILD_TARGET = arch/x86/boot/bzImage # The place to put your image on the test machine #TARGET_IMAGE = /boot/vmlinuz-test # A script or command to reboot the box # # Here is a digital loggers power switch example #POWER_CYCLE = wget --no-proxy -O /dev/null -q --auth-no-challenge 'http://admin:admin@power/outlet?5=CCL' # # Here is an example to reboot a virtual box on the current host # with the name "Guest". #POWER_CYCLE = virsh destroy Guest; sleep 5; virsh start Guest # The script or command that reads the console # # If you use ttywatch server, something like the following would work. #CONSOLE = nc -d localhost 3001 # # For a virtual machine with guest name "Guest". #CONSOLE = virsh console Guest # Signal to send to kill console. # ktest.pl will create a child process to monitor the console. # When the console is finished, ktest will kill the child process # with this signal. # (default INT) #CLOSE_CONSOLE_SIGNAL = HUP # Required version ending to differentiate the test # from other linux builds on the system. #LOCALVERSION = -test # For REBOOT_TYPE = grub2, you must specify where the grub.cfg # file is. This is the file that is searched to find the menu # option to boot to with GRUB_REBOOT #GRUB_FILE = /boot/grub2/grub.cfg # The tool for REBOOT_TYPE = grub2 to set the next reboot kernel # to boot into (one shot mode). # (default grub2_reboot) #GRUB_REBOOT = grub2_reboot # The grub title name for the test kernel to boot # (Only mandatory if REBOOT_TYPE = grub or grub2) # # Note, ktest.pl will not update the grub menu.lst, you need to # manually add an option for the test. ktest.pl will search # the grub menu.lst for this option to find what kernel to # reboot into. # # For example, if in the /boot/grub/menu.lst the test kernel title has: # title Test Kernel # kernel vmlinuz-test # # For grub2, a search of top level "menuentry"s are done. No # submenu is searched. The menu is found by searching for the # contents of GRUB_MENU in the line that starts with "menuentry". # You may want to include the quotes around the option. For example: # for: menuentry 'Test Kernel' # do a: GRUB_MENU = 'Test Kernel' # For customizing, add your entry in /etc/grub.d/40_custom. # #GRUB_MENU = Test Kernel # For REBOOT_TYPE = syslinux, the name of the syslinux executable # (on the target) to use to set up the next reboot to boot the # test kernel. # (default extlinux) #SYSLINUX = syslinux # For REBOOT_TYPE = syslinux, the path that is passed to to the # syslinux command where syslinux is installed. # (default /boot/extlinux) #SYSLINUX_PATH = /boot/syslinux # For REBOOT_TYPE = syslinux, the syslinux label that references the # test kernel in the syslinux config file. # (default undefined) #SYSLINUX_LABEL = "test-kernel" # A script to reboot the target into the test kernel # This and SWITCH_TO_TEST are about the same, except # SWITCH_TO_TEST is run even for REBOOT_TYPE = grub. # This may be left undefined. # (default undefined) #REBOOT_SCRIPT = #### Optional Config Options (all have defaults) #### # Start a test setup. If you leave this off, all options # will be default and the test will run once. # This is a label and not really an option (it takes no value). # You can append ITERATE and a number after it to iterate the # test a number of times, or SKIP to ignore this test. # #TEST_START #TEST_START ITERATE 5 #TEST_START SKIP # Have the following options as default again. Used after tests # have already been defined by TEST_START. Optionally, you can # just define all default options before the first TEST_START # and you do not need this option. # # This is a label and not really an option (it takes no value). # You can append SKIP to this label and the options within this # section will be ignored. # # DEFAULTS # DEFAULTS SKIP # If you want to execute some command before the first test runs # you can set this option. Note, it can be set as a default option # or an option in the first test case. All other test cases will # ignore it. If both the default and first test have this option # set, then the first test will take precedence. # # default (undefined) #PRE_KTEST = ${SSH} ~/set_up_test # If you want to execute some command after all the tests have # completed, you can set this option. Note, it can be set as a # default or any test case can override it. If multiple test cases # set this option, then the last test case that set it will take # precedence # # default (undefined) #POST_KTEST = ${SSH} ~/dismantle_test # The default test type (default test) # The test types may be: # build - only build the kernel, do nothing else # install - build and install, but do nothing else (does not reboot) # boot - build, install, and boot the kernel # test - build, boot and if TEST is set, run the test script # (If TEST is not set, it defaults back to boot) # bisect - Perform a bisect on the kernel (see BISECT_TYPE below) # patchcheck - Do a test on a series of commits in git (see PATCHCHECK below) #TEST_TYPE = test # Test to run if there is a successful boot and TEST_TYPE is test. # Must exit with 0 on success and non zero on error # default (undefined) #TEST = ssh user@machine /root/run_test # The build type is any make config type or special command # (default randconfig) # nobuild - skip the clean and build step # useconfig:/path/to/config - use the given config and run # oldconfig on it. # This option is ignored if TEST_TYPE is patchcheck or bisect #BUILD_TYPE = randconfig # The make command (default make) # If you are building a 32bit x86 on a 64 bit host #MAKE_CMD = CC=i386-gcc AS=i386-as make ARCH=i386 # Any build options for the make of the kernel (not for other makes, like configs) # (default "") #BUILD_OPTIONS = -j20 # If you need to do some special handling before installing # you can add a script with this option. # The environment variable KERNEL_VERSION will be set to the # kernel version that is used. # # default (undefined) #PRE_INSTALL = ssh user@target rm -rf '/lib/modules/*-test*' # If you need an initrd, you can add a script or code here to install # it. The environment variable KERNEL_VERSION will be set to the # kernel version that is used. Remember to add the initrd line # to your grub menu.lst file. # # Here's a couple of examples to use: #POST_INSTALL = ssh user@target /sbin/mkinitrd --allow-missing -f /boot/initramfs-test.img $KERNEL_VERSION # # or on some systems: #POST_INSTALL = ssh user@target /sbin/dracut -f /boot/initramfs-test.img $KERNEL_VERSION # If for some reason you just want to boot the kernel and you do not # want the test to install anything new. For example, you may just want # to boot test the same kernel over and over and do not want to go through # the hassle of installing anything, you can set this option to 1 # (default 0) #NO_INSTALL = 1 # If there is a command that you want to run before the individual test # case executes, then you can set this option # # default (undefined)