/* * Copyright 2012-2013 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. */ #include <linux/interrupt.h>#include <linux/clockchips.h>#include <linux/clk.h>#include <linux/of_address.h>#include <linux/of_irq.h>#include <linux/sched_clock.h> /* * Each pit takes 0x10 Bytes register space */#define PITMCR		0x00#define PIT0_OFFSET	0x100#define PITn_OFFSET(n)	(PIT0_OFFSET + 0x10 * (n))#define PITLDVAL	0x00#define PITCVAL		0x04#define PITTCTRL	0x08#define PITTFLG		0x0c #define PITMCR_MDIS	(0x1 << 1) #define PITTCTRL_TEN	(0x1 << 0)#define PITTCTRL_TIE	(0x1 << 1)#define PITCTRL_CHN	(0x1 << 2) #define PITTFLG_TIF	0x1 static void __iomem *clksrc_base;static void __iomem *clkevt_base;static unsigned long cycle_per_jiffy; static inline void pit_timer_enable(void){	__raw_writel(PITTCTRL_TEN | PITTCTRL_TIE, clkevt_base + PITTCTRL);} static inline void pit_timer_disable(void){	__raw_writel(0, clkevt_base + PITTCTRL);} static inline void pit_irq_acknowledge(void){	__raw_writel(PITTFLG_TIF, clkevt_base + PITTFLG);} static u64 pit_read_sched_clock(void){	return ~__raw_readl(clksrc_base + PITCVAL);} static int __init pit_clocksource_init(unsigned long rate){	/* set the max load value and start the clock source counter */	__raw_writel(0, clksrc_base + PITTCTRL);	__raw_writel(~0UL, clksrc_base + PITLDVAL);	__raw_writel(PITTCTRL_TEN, clksrc_base + PITTCTRL); 	sched_clock_register(pit_read_sched_clock, 32, rate);	return clocksource_mmio_init(clksrc_base + PITCVAL, "vf-pit", rate,			300, 32, clocksource_mmio_readl_down);} static int pit_set_next_event(unsigned long delta,				struct clock_event_device *unused){	/*	 * set a new value to PITLDVAL register will not restart the timer,	 * to abort the current cycle and start a timer period with the new	 * value, the timer must be disabled and enabled again.	 * and the PITLAVAL should be set to delta minus one according to pit	 * hardware requirement.	 */	pit_timer_disable();	__raw_writel(delta - 1, clkevt_base + PITLDVAL);	pit_timer_enable(); 	return 0;} static void pit_set_mode(enum clock_event_mode mode,				struct clock_event_device *evt){	switch (mode) {	case CLOCK_EVT_MODE_PERIODIC:		pit_set_next_event(cycle_per_jiffy, evt);		break;	default:		break;	}} static irqreturn_t pit_timer_interrupt(int irq, void *dev_id){	struct clock_event_device *evt = dev_id; 	pit_irq_acknowledge(); 	/*	 * pit hardware doesn't support oneshot, it will generate an interrupt	 * and reload the counter value from PITLDVAL when PITCVAL reach zero,	 * and start the counter again. So software need to disable the timer	 * to stop the counter loop in ONESHOT mode.	 */	if (likely(evt->mode == CLOCK_EVT_MODE_ONESHOT))		pit_timer_disable(); 	evt->event_handler(evt); 	return IRQ_HANDLED;} static struct clock_event_device clockevent_pit = {	.name		= "VF pit timer",	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,	.set_mode	= pit_set_mode,	.set_next_event	= pit_set_next_event,	.rating		= 300,}; static struct irqaction pit_timer_irq = {	.name		= "VF pit timer",	.flags		= IRQF_TIMER | IRQF_IRQPOLL,	.handler	= pit_timer_interrupt,	.dev_id		= &clockevent_pit,}; static int __init pit_clockevent_init(unsigned long rate, int irq){	__raw_writel(0, clkevt_base + PITTCTRL);	__raw_writel(PITTFLG_TIF, clkevt_base + PITTFLG); 	BUG_ON(setup_irq(irq, &pit_timer_irq)); 	clockevent_pit.cpumask = cpumask_of(0);	clockevent_pit.irq = irq;	/*	 * The value for the LDVAL register trigger is calculated as:	 * LDVAL trigger = (period / clock period) - 1	 * The pit is a 32-bit down count timer, when the conter value	 * reaches 0, it will generate an interrupt, thus the minimal	 * LDVAL trigger value is 1. And then the min_delta is	 * minimal LDVAL trigger value + 1, and the max_delta is full 32-bit.	 */	clockevents_config_and_register(&clockevent_pit, rate, 2, 0xffffffff); 	return 0;} static void __init pit_timer_init(struct device_node *np){	struct clk *pit_clk;	void __iomem *timer_base;	unsigned long clk_rate;	int irq; 	timer_base = of_iomap(np, 0);	BUG_ON(!timer_base); 	/*	 * PIT0 and PIT1 can be chained to build a 64-bit timer,	 * so choose PIT2 as clocksource, PIT3 as clockevent device,	 * and leave PIT0 and PIT1 unused for anyone else who needs them.	 */	clksrc_base = timer_base + PITn_OFFSET(2);	clkevt_base = timer_base + PITn_OFFSET(3); 	irq = irq_of_parse_and_map(np, 0);	BUG_ON(irq <= 0); 	pit_clk = of_clk_get(np, 0);	BUG_ON(IS_ERR(pit_clk)); 	BUG_ON(clk_prepare_enable(pit_clk)); 	clk_rate = clk_get_rate(pit_clk);	cycle_per_jiffy = clk_rate / (HZ); 	/* enable the pit module */	__raw_writel(~PITMCR_MDIS, timer_base + PITMCR); 	BUG_ON(pit_clocksource_init(clk_rate)); 	pit_clockevent_init(clk_rate, irq);}CLOCKSOURCE_OF_DECLARE(vf610, "fsl,vf610-pit", pit_timer_init);