Revised: 2004-Oct-21 This is the documentation of (hopefully) all possible error codes (andtheir interpretation) that can be returned from usbcore. Some of them are returned by the Host Controller Drivers (HCDs), whichdevice drivers only see through usbcore.  As a rule, all the HCDs shouldbehave the same except for transfer speed dependent behaviors and theway certain faults are reported.  ***************************************************************************                   Error codes returned by usb_submit_urb               *************************************************************************** Non-USB-specific: 0		URB submission went fine -ENOMEM		no memory for allocation of internal structures	 USB-specific: -EBUSY		The URB is already active. -ENODEV		specified USB-device or bus doesn't exist -ENOENT		specified interface or endpoint does not exist or		is not enabled -ENXIO		host controller driver does not support queuing of this type		of urb.  (treat as a host controller bug.) -EINVAL		a) Invalid transfer type specified (or not supported)		b) Invalid or unsupported periodic transfer interval		c) ISO: attempted to change transfer interval		d) ISO: number_of_packets is < 0		e) various other cases -EXDEV		ISO: URB_ISO_ASAP wasn't specified and all the frames		the URB would be scheduled in have already expired. -EFBIG		Host controller driver can't schedule that many ISO frames. -EPIPE		The pipe type specified in the URB doesn't match the		endpoint's actual type. -EMSGSIZE	(a) endpoint maxpacket size is zero; it is not usable		    in the current interface altsetting.		(b) ISO packet is larger than the endpoint maxpacket.		(c) requested data transfer length is invalid: negative		    or too large for the host controller. -ENOSPC		This request would overcommit the usb bandwidth reserved		for periodic transfers (interrupt, isochronous). -ESHUTDOWN	The device or host controller has been disabled due to some		problem that could not be worked around. -EPERM		Submission failed because urb->reject was set. -EHOSTUNREACH	URB was rejected because the device is suspended. -ENOEXEC	A control URB doesn't contain a Setup packet.  ***************************************************************************                   Error codes returned by in urb->status               **                   or in iso_frame_desc[n].status (for ISO)             *************************************************************************** USB device drivers may only test urb status values in completion handlers.This is because otherwise there would be a race between HCDs updatingthese values on one CPU, and device drivers testing them on another CPU. A transfer's actual_length may be positive even when an error has beenreported.  That's because transfers often involve several packets, so thatone or more packets could finish before an error stops further endpoint I/O. For isochronous URBs, the urb status value is non-zero only if the URB isunlinked, the device is removed, the host controller is disabled, or the totaltransferred length is less than the requested length and the URB_SHORT_NOT_OKflag is set.  Completion handlers for isochronous URBs should only seeurb->status set to zero, -ENOENT, -ECONNRESET, -ESHUTDOWN, or -EREMOTEIO.Individual frame descriptor status fields may report more status codes.  0			Transfer completed successfully -ENOENT			URB was synchronously unlinked by usb_unlink_urb -EINPROGRESS		URB still pending, no results yet			(That is, if drivers see this it's a bug.) -EPROTO (*, **)		a) bitstuff error			b) no response packet received within the			   prescribed bus turn-around time			c) unknown USB error  -EILSEQ (*, **)		a) CRC mismatch			b) no response packet received within the			   prescribed bus turn-around time			c) unknown USB error  			Note that often the controller hardware does not			distinguish among cases a), b), and c), so a			driver cannot tell whether there was a protocol			error, a failure to respond (often caused by			device disconnect), or some other fault. -ETIME (**)		No response packet received within the prescribed			bus turn-around time.  This error may instead be			reported as -EPROTO or -EILSEQ. -ETIMEDOUT		Synchronous USB message functions use this code			to indicate timeout expired before the transfer			completed, and no other error was reported by HC. -EPIPE (**)		Endpoint stalled.  For non-control endpoints,			reset this status with usb_clear_halt(). -ECOMM			During an IN transfer, the host controller			received data from an endpoint faster than it			could be written to system memory -ENOSR			During an OUT transfer, the host controller			could not retrieve data from system memory fast			enough to keep up with the USB data rate -EOVERFLOW (*)		The amount of data returned by the endpoint was			greater than either the max packet size of the			endpoint or the remaining buffer size.  "Babble". -EREMOTEIO		The data read from the endpoint did not fill the			specified buffer, and URB_SHORT_NOT_OK was set in			urb->transfer_flags. -ENODEV			Device was removed.  Often preceded by a burst of			other errors, since the hub driver doesn't detect			device removal events immediately. -EXDEV			ISO transfer only partially completed			(only set in iso_frame_desc[n].status, not urb->status) -EINVAL			ISO madness, if this happens: Log off and go home -ECONNRESET		URB was asynchronously unlinked by usb_unlink_urb -ESHUTDOWN		The device or host controller has been disabled due			to some problem that could not be worked around,			such as a physical disconnect.  (*) Error codes like -EPROTO, -EILSEQ and -EOVERFLOW normally indicatehardware problems such as bad devices (including firmware) or cables. (**) This is also one of several codes that different kinds of hostcontroller use to indicate a transfer has failed because of devicedisconnect.  In the interval before the hub driver starts disconnectprocessing, devices may receive such fault reports for every request.   ***************************************************************************              Error codes returned by usbcore-functions                 **           (expect also other submit and transfer status codes)         *************************************************************************** usb_register():-EINVAL			error during registering new driver usb_get_*/usb_set_*():usb_control_msg():usb_bulk_msg():-ETIMEDOUT		Timeout expired before the transfer completed.